General
| Type | Torque (Nm) |
|---|---|
| 5 mm bolt, nut | 5 |
| 6 mm bolt, nut | 10 |
| 8 mm bolt, nut | 22 |
| 10 mm bolt, nut | 35 |
| 12 mm bolt, nut | 55 |
| 5 mm screw | 4 |
| 6 mm screw, 6 mm bolt with 8 mm head | 9 |
| 6 mm flange bolt, nut | 12 |
| 8 mm flange bolt, nut | 27 |
| 10 mm flange bolt, nut | 40 |
Engine (Hawk GT)
| Item | Quantity | Thread diamter (mm) | Torque (Nm) | Remark |
|---|---|---|---|---|
| Spark plug | 4 | 12 | 14 | - |
| Cylinder head cover bolt | 4 | 6 | 10 | Special bolt |
| Cam shaft holder 8 mm bolt | 6 | 8 | 23 | - |
| Cam shaft holder 8 mm nut | 2 | 8 | 23 | - |
| Cam shaft holder 6 mm bolt | 4 | 6 | 10 | - |
| Cylinder head 10 mm nut | 8 | 10 | 48 | - |
| Cylinder head 8 mm bolt | 4 | 8 | 23 | - |
| Cylinder head 8 mm nut | 4 | 8 | 23 | - |
| Cylinder head 6 mm bolt | 2 | 6 | 10 | Socket bolt |
| Cam shaft sprocket bolt | 4 | 7 | 23 | Apply locking agent to threads |
| Clutch lock nut | 1 | 18 | 130 | Staked nut |
| Right crankcase cover bolt | 15 | 6 | 10 | - |
| Left crankcase cover bolt | 9 | 6 | 10 | - |
| Oil filter cartridge | 1 | 20 | 10 | Apply engine oil to O-ring |
| Oil drain bolt | 1 | 14 | 35 | - |
| Neutral switch | 1 | 10 | 12 | - |
| Oil pressure switch | 1 | - | 12 | Apply sealant to threads |
| Primary drive gear bolt | 1 | 12 | 90 | UBS bolt, Apply engine oil to threads |
| Flywheel bolt | 1 | 12 | 130 | Left hand thread, Apply engine oil to threads |
| Starter one way clutch | 6 | 8 | 30 | Torx bolt, apply locking agent to threads |
| Oil control bolt | 1 | 10 | 23 | - |
| Oil pipe bolt | 2 | 7 | 10 | Special bolt |
| Connecting rod cap nut | 4 | 8 | 34 | - |
| Crankcase 8 mm bolt | 14 | 8 | 27 | Apply engine oil to threads |
| Crankcase 6 mm bolt | 6 | 6 | 12 | Apply engine oil to threads |
| Shift drum stopper plate bolt | 1 | 6 | 26 | Apply locking agent to threads |
| Insulator band screw | 4 | 5 | 4 | Apply engine oil to threads |
| Timing hole cap | 1 | 14 | 10 | Apply molybdenum disulfide grease to threads |
| Crankshaft hole cap | 14 | 30 | 15 | Apply molybdenum disulfide grease to threads |
| Oil pump driven sprocket bolt | 1 | 6 | 15 | Apply locking agent to threads |
| Valve adjusting screw lock nut | 6 | 7 | 23 | - |
| Cylinder stud bolt 8mm | 2 | 8 | 20-30 | Apply locking agent to threads, refer to section 10 |
| Cylinder stud bolt 10 mm | 8 | 10 | 30-50 | Apply locking agent to threads, refer to section 10 |
Frame (Hawk GT)
| Item | Quantity | Thread diameter (mm) | Torque (Nm) | Remark |
|---|---|---|---|---|
| Front engine bracket bolt | 4 | 8 | 28 | - |
| Front engine mounting bolt | 1 | 10 | 40 | - |
| Rear upper engine mounting bolt | 1 | 10 | 40 | Apply engine oil to threads |
| Rear upper engine mounting bolt lock nut | 1 | 22 | 55 | - |
| Rear upper engine mounting bolt adjusting bolt | 1 | 22 | 11 | - |
| Gearshift arm bolt | 1 | 6 | 12 | - |
| Thermostatic switch | 1 | 16 | 18 | Apply sealant to threads |
| Exhaust pipe joint nut | 4 | 8 | 27 | - |
| Muffler band bolt | 1 | 8 | 27 | - |
| Muffler mounting bolt | 2 | 8 | 27 | - |
| Fuel tank mounting bolt front | 1 | 6 | 12 | - |
| Fuel tank mounting bolt rear | 1 | 8 | 22 | - |
| Fuel filter bracket bolt | 1 | 6 | 22 | - |
| Front brake master cylinder holder | 2 | 6 | 12 | - |
| Brake oil bolt | 4 | 10 | 30 | - |
| Brake reservoir screw | 4 | 4 | 1.5 | - |
| Bleed valve | 2 | 7 | 6 | - |
| Front caliper mounting bolt | 2 | 8 | 27 | Flange bolt |
| Front caliper pin bolt | 2 | 10 | 28 | - |
| Pad pin | 2 | 10 | 17 | - |
| Pad pin plug | 2 | 10 | 2.5 | - |
| Front brake disc retaining bolt | 6 | 8 | 40 | Apply thread locker to threads |
| Rear brake reservoir mounting screw | 1 | 6 | 9 | - |
| Rear brake disc retaining bolt | 4 | 8 | 35 | - |
| Rear brake disc retaining bolt lock nut | 1 | 8 | 9 | - |
| Rear caliper mounting bolt | 2 | 8 | 27 | - |
| Rear caliper pivot bolt | 1 | 8 | 22 | - |
| Brake torque rod bolt | 2 | 10 | 35 | - |
| Handlebar pinch bolt (Hawk GT) | 2 | 8 | 27 | - |
| Ignition switch bolt mounting bolt | 2 | 8 | 25 | - |
| Fork pinch bolt (upper) | 2 | 7 | 11 | - |
| Fork pinch bolt (lower) | 2 | 10 | 50 | Apply engine oil to threads |
| Fork tube cap | 2 | - | 23 | - |
| Fork socket bolt | 2 | 8 | 17 | Apply thread locker to threads |
| Steering bearing adjustment nut | 1 | 26 | 20 | Apply engine oil to threads |
| Steering stem nut | 1 | 24 | 105 | Flange nut |
| Front axle bolt | 1 | 14 | 60 | - |
| Front axle pinch bolt | 4 | 8 | 22 | - |
| Rear wheel nut | 1 | 18 | 120 | - |
| Eccentric bearing carrier lock nut | 1 | 35 | 165 | Staked nut |
| Shock absorber upper mounting bolt | 1 | 12 | 65 | Flange bolt |
| Shock absorber lower mounting bolt | 1 | 10 | 45 | Cap nut |
| Shock absorber damper rod lock nut | 1 | 14 | 62 | Apply thread locker to threads |
| Swingarm adjusting bolt | 1 | 26 | 15 | - |
| Swingarm adjusting bolt lock nut | 1 | 26 | 65 | - |
| Swingarm pivot nut | 1 | 14 | 65 | - |
| Eccentric bearing carrier pinch bolt | 1 | 16 | 75 | - |
| Driven sprocket mounting bolt | 6 | 8 | 43 | - |
| Foot peg bracket bolt | 4 | 8 | 27 | - |
| Sub frame mounting bolt | 4 | 10 | 40 | - |
| Side stand pivot bolt | 1 | 10 | 38 | - |
| Side stand bracket bolt | 2 | 8 | 28 | - |
| Center stand mounting bolt | 2 | 10 | 55 | Using a box wrench |
| Ignition switch mounting bolt | 2 | 6 | 25 | Torx bolt |